
One of these common types is the spur gear which consists of straight teeth on a round body meshed along parallel shafts. For decades it has been used in circumstances where speed and cost efficiencies are important — reducers, pump drives, agricultural implements. YIZHI MACHINERY custom manufactures spur gears to ISO 1328 grades 6 to 8, some parts up to grade 5. This covers spur gear design, materials, heat treatments, machining, inspection, and when to use a helical gear.
What Makes a Spur Gear the Workhorse of Parallel Drives
The teeth run straight and parallel to the shaft axis. During meshing the tooth forces have tangential and radial components, but no axial thrust is generated by the gear mesh. Fewer axial bearing constraints. Since efficiency is a paramount concern in moderate and low speed operation, spur gear pairs usually operate at 95 to 99 percent efficiencies despite both rolling and sliding between their flanks. The trade-off is noise. Contact from one tooth to another occurs simultaneously across the face width so spur gears are usually noisier than helical gears. Helical or herringbone gears are normally used for higher-speed, high-load drives; spur gears stay common in low cost mid-range work. It ends with price and efficiency. When the teeth geometry is straight, it would be one of the easiest to cut and inspect (and rework), leading to a lower unit price for volume runs while still being repeatable. We also provide a custom spur gear range designed to match the sizes and precision classes required by parallel-shaft drives.
Designing a Spur Gear Around Your Application

Module, Pressure Angle, and Tooth Count
One small set of numbers establishes a spur gear. Module: m = d / z (d reference diameter, z – number of teeth). Pressure angle impacts flank slope; the standard today is 20 degrees, while some legacy work used a pressure angle of just 14.5 degrees or so. Center distance depends on the module, tooth counts of both gears and any profile shift; the reference diameter depends on module and tooth count. This is where most design reviews start – with center distance. If the housing (or frame) fixes it, the module, tooth counts and any profile shift must fit that constraint.
Modified Gears for Center Distance and Interference Control
What basic geometry cannot handle, addendum modification (or profile shift) can. A positive profile shift on a small pinion reduces the risk of tooth root undercut. Two gears that are matched and shifted can create a center distance, which natively an unmodified pair of the same modulus cannot reach. On a replacement gear, the shift coefficient is as critical to tooth number — different shifts will affect backlash and tooth thickness — so take that data from the original drawing for that mesh.
Materials and Heat Treatment That Extend Spur Gear Life
All materials are selected based on load and speed. Carbon steel: the most common base material, low-cost and easy to machine; also good for induction hardening. Carburizing steels for pinions permit a hard case on top of a tough core, while chromium-molybdenum alloy steels are suitable for fatigue-critical components.
Matching Material and Surface Hardness to Load
These pinions undergo the standard carburizing and quenching process. The case can be as hard as 55–60 HRC, with the depth of the case selected for that gear while having enough toughness in core to successfully transmit shock loading. Where through-hardening is suitable, quenching and tempering delivers an intermediate hardness level that balances the best of both worlds. For example, on 45 steel and shaft-type gears of 42CrMo, surface hardness is increased for heavily loaded parts by induction hardening. Because accuracy might be affected by heat treatment, the part is often ground afterward unless dimensional restrictions do not allow for this. You can use blackening, phosphating or galvanizing for corrosion protection, if needed; shot peening creates compressive stresses at the surface to improve fatigue resistance. Overall blackening, phosphating and galvanizing are more for corrosion protection, not tooth wear since the flanks of a gear tooth are hardened and carry the contact load.
How a Custom Spur Gear Is Made and Inspected
The OEM process has five stages:
- Demand communication
- Design and drawing
- Manufacturing & Processing
- Quality inspection
- Packing & Shipping.
Incoming material is spectrometrically checked before being cut; a part that does not pass an inspection stage cannot move on

Gear Cutting, Grinding, and Finishing
Pre-treatment — normalizing or quenching and tempering (depending on material + final heat treatment). Rough machining follows. Hobbing is the most common process for spur gear production, but when hobbing cannot reach or internal teeth are needed (for ring-type work), shaping is used instead. Grinding both compensates for heat-treatment distortion and gets profile accuracy. Keyways and splines can be broached or milled, whilst end faces may be machined or ground.
Inspection Against ISO 1328
Tooth accuracy is verified against ISO 1328 with most of the work at grades 6 to 8 and some parts at grade 5. The inspection tools consist of gear measuring machines for profile and pitch, a coordinate measuring machine (CMM) to measure dimensions, standard common-normal micrometers, a hardness tester as well as runout gauges and meshing inspectors. Check the specified dimensions and tolerances against the drawing.
Selecting the Right Spur Gear
The practical question in most specifications is spur versus helical.
Spur Versus Helical: A Practical Trade-Off
Helical gears of equal size can bear higher load due to the overlap in tooth contact, and are quieter. They create axial thrust so the bearings have to be rated for that load, and cutting has a higher cost. In designs where speed, load or noise are limiting – compressors, machine-tool spindles and metro drives — helical gears often represent a more sensible foundation. Use spur gears when speed is not so high and cost or ease of manufacture leans toward simplicity. Our own industrial applications YIZHI MACHINERY serves — air compressors, pumps, general machinery, agriculture and mining follow this trend.
Conclusion
The proper design of a spur gear built to order relies on simplicity: the right tooth profile; an appropriate carbon or alloy steel that has been hardened correctly; and testing (with documentation). And for parallel-shaft drives that require predictable cost, ease of use and proven reliability, it is still a workhorse. Reach out to our team for spur gears cut-to-print in carbon or alloy steel, with heat treatment and inspection according to ISO 1328 — we can start designing from your drawings or even just a description of how it is supposed to work
Frequently Asked Questions
Q: What is the most common material for a custom spur gear?
For many custom spur gears, carbon steel is the base material. It has good machinability and can be made cheap in volume, plus it lends itself well to surface hardening by induction. High fatigue loads may require chromium-molybdenum steels, and low-alloy carburizing steel suits pinions requiring a hardened case over a tough core. This is a function of load, speed and the heat-treatment route.
Q: What accuracy grade do YIZHI MACHINERY spur gears meet?
They are manufactured to ISO 1328 grades between 6 and 8, with some parts made to grade 5. A tighter grade means tighter profile and pitch tolerances and more inspection (often grinding after heat treatment); better to specify the grade prior to the first article.
Q: When should I choose a spur gear over a helical gear?
For low-to-moderate-speed, parallel-shaft drives where lower cost and simpler bearing arrangements are preferred without axial thrust, a spur gear can be used. When load or speed is increasing or noise becomes the limit value then helical gears may be preferred, but these need bearings that can withstand axial thrusts.
Q: What information does the manufacturer need to quote a spur gear?
Minimum information: module, number of teeth, pressure angle, pitch diameter (if known), bore diameter, overall length and face width, material, heat-treatment specification and accuracy grade — preferably on a drawing. In cases where only a functional description exists, the OEM design and drawing stage may fill in missing or unclear details to provide an answer.

